ProppFrexx ONAIR User-Forum

Hello all

I have the following question: I cannot join/set my DR Airance mixer in the first screen of the GPIO.
In the second screen I get the message as in the photo, what am I doing wrong

Kind regards, Bob van Dongen

communication between PF and the D&R maybe you will find the solution here http://www.mambanet.org/wiki/dokuwiki/d ... ence:start

Thanks for your response
I cannot enable the D&R Airance control in the GPIO

Maybe you are already using another (Airence ) app in parallel? That’s the only case I so far heard, why it could not connect, as the Airence only allows one app to use the API to it.
Or you are using a USB hub or defect USB cable.

Thank you for your message Bernd

When I connect the mixer to my old PC, which I was able to work well with until a few days ago with the Gpio connection, it still works well now.

But it doesn't work on my new PC where I installed Proppfrexx yesterday.

Could it be that it doesn't work because I have the mixer connected to a USB 3.0 connection? I no longer have 2.0 USB connections.

I cannot transfer the D&R Airance choice to online

regards

Another update, I don't know if it matters but my windows is a windows 11 Pro.
Can't get the D&R enabled in the GPIO yet. Does anyone else have a golden tip???

This is the Error write from the folder

C:\Users\Bob Van Dongen\AppData\Roaming\radio42\ProppFrexx GPIOClient\4.0



1-2-2024 22:12:57 [v4.4.3.3]:********** Error/Exception Information **********
Error Message: Kan DLL BioDaq.dll niet laden: Kan opgegeven module niet vinden. (Uitzondering van HRESULT: 0x8007007E)
Error Type: System.DllNotFoundException
Error Source: Automation.BDaq4.Automation.BDaq.ErrorCode SnapStop(IntPtr)
********** System Stack Trace **********
bij Automation.BDaq.TInstantDiCtrl.SnapStop(IntPtr obj)
bij Automation.BDaq.InstantDiCtrl.DeinitializeControl()
bij Automation.BDaq.DaqCtrlBase.Dispose(Boolean disposing)
bij Automation.BDaq.DaqCtrlBase.Finalize()
********** Environment Stack Trace **********
bij System.Environment.GetStackTrace(Exception e, Boolean needFileInfo)
bij System.Environment.get_StackTrace()
bij ProppFrexx.MainForm.GetExceptionInfo(Exception e, Boolean full)
bij ProppFrexx.MainForm.WriteErrorLog(Exception e)
bij ProppFrexx.MainForm.UnhandledExceptionHandler(Exception e)
bij ProppFrexx.MainForm.CustomExceptionHandler(Object sender, UnhandledExceptionEventArgs args)
bij Automation.BDaq.TInstantDiCtrl.SnapStop(IntPtr obj)
bij Automation.BDaq.InstantDiCtrl.DeinitializeControl()
bij Automation.BDaq.DaqCtrlBase.Dispose(Boolean disposing)
bij Automation.BDaq.DaqCtrlBase.Finalize()
********** End **********

radio42 wrote: 01 Feb 2024 19:48 Maybe you are already using another (Airence ) app in parallel? That’s the only case I so far heard, why it could not connect, as the Airence only allows one app to use the API to it.
Or you are using a USB hub or defect USB cable.

I replaced the USB cable with another one and that made no difference. The USB cable is connected directly to the motherboard in a USB 2.0 Type A port

Greetings Bob van Dongen

The error indicates, that it can not load a certain file, which seems to be needed.
In the regular ProppFrexx installation it installes a DLL called "Automation.BDaq4.dll" - which is a DLL b´needed for an Advantech GPIO board.
However, that DLL has nothing to do with the Airence mixer !!

Are you using an Advantech USB card as well?, which is maybe crashing your GPIO?

radio42 wrote: 01 Feb 2024 23:24 The error indicates, that it can not load a certain file, which seems to be needed.
In the regular ProppFrexx installation it installes a DLL called "Automation.BDaq4.dll" - which is a DLL b´needed for an Advantech GPIO board.
However, that DLL has nothing to do with the Airence mixer !!

Are you using an Advantech USB card as well?, which is maybe crashing your GPIO?

I use this motherboard and the Airence is on a USB 2.0


https://www.msi.com/Motherboard/Z790-GAMING-PLUS-WIFI